|

How To Make A Pendant Light With Drinking Straws

Here’s another DIY project that fell through the cracks when I switched to WordPress. This was the very first DIY project I ever did for Addicted 2 Decorating, originally posted in July 2008, and it was before the days that I realized I needed to be taking pictures of each step of the process. Blogging DIY projects has certainly been a learning process! I hope you enjoy this blast from the past!

This drinking straw pendant light is a fun and fairly easy DIY lighting project that is sure to add great texture to your room. It’s also sure to be a great conversation piece! After all, who would have thought that such humble materials as drinking straws could look so great!?

This drinking straw light would be a fun addition to a child’s room, a play room, or anywhere you’d like to add some fun and color. Or you could use all white straws, or all translucent straws, for a more mature look that would work well in just about any room of your home.


**Please read the helpful hints section before beginning this project.

Project Cost:

Approximately $40

Tools & Materials:

  • 1 roll of metal hardware cloth with 1/2 inch grid (found in the home improvement store with the “chicken coop” wire),
  • Wire lampshade ring with washer top in the diameter of your choice,
  • 22 gauge craft wire (most hardware cloth is wrapped in wire. If this is the case, you will not need additional wire),
  • 1500 drinking straws (number will vary depending on size of shade),
  • Pendant light wiring kit (sometimes called a swag light wiring kit. Light socket may have to be purchased separately);
  • Scissors,
  • Pliers,
  • Sidecutter wire snips,
  • Lots and lots of patience!

 

Instructions:

1. Remove old lamp shade fabric from the wire hoop. You will only need the top hoop.

2. Begin wrapping the hardware cloth around the metal hoop to form a drum shade. Secure with craft wire.

3. Once you’ve wrapped the hardware cloth all the way around the hoop, overlap the hardware cloth about 1 inch, and use your side cutter wire snips to cut off the excess hardware cloth.

4. Using the craft wire, secure the hardware cloth where it overlaps to create a drum lamp shade form. (A drum shade has the same diameter on top and on bottom.)

5. Using your side cutter wire snips, cut the shade to the desired height.

6. Prepare your straws by cutting them in half. There’s no need to be perfect with this step. The slight variations in length will add a textural quality to the finished shade.

7. Begin inserting the straws by folding each one in half, and from the inside of the lampshade form, push the straw through to the outside of the shade, making sure that the straw wraps around the wire of the hardware cloth.

8. Continue the process until all of the wires are covered by a straw. Each 1/2 inch opening will end up with 4 straws through it.

9. Finish the very top row, and the very bottom row, with a double layer of straws.

10. Finish the light by following the instructions on the pendant light kit to wire the lighting.

11. Hang the light, and enjoy!

Helpful Hints:

    • This project is not appropriate for small children. The hardware cloth can be difficult to work with, and when it’s cut, it leaves sharp edges that can injure children (and adults!). Please handle the hardware cloth with caution.
    • Due to sharp edges on the finished product, please keep this lamp shade out of the reach of children. It should be hung in an area where it can be enjoyed, but not touched or handled.
    • Keep in mind that your finished shade will be about four inches larger in diameter than the hoop size you started with.
    • When inserting the straws, it’s easiest to start in the middle of the shade and work up towards the top. When you have half of the shade completed, flip the shade over, begin in the middle again, and work up towards the top.

 

Variations:

    • For a more mature, contemporary look, use one color for the entire shade. White or translucent straws create a beautiful contemporary shade, but you can also use red, blue, etc.
    • For a child’s room, use multi-colored neon straws (as shown in picture above.
    • For a mature, contemporary look with a bit more variety, mix translucent and white straws.

 

 

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

13 Comments

  1. Hello,

    Is there anyway you could make some of these lights for me? How much would you charge me per light? Also – what is the size of this light? Do you think it could be made in the shape of a circle? Just curious but the way you did it is gorgeous. Please let me know if you can make this for me. I have no artistic talent (or time) 🙁

    Sincerely,

    Faith Gil

  2. Just saw this in a post from Homemade Ideas and Instructions, they DID have your website name on the bottom of the picture. Just letting you know.